EAN: 3760244880260 SKU ALE1210 Categories , Tag

PRECISE : Output ripple < 3 mV rms.
COMPLIE : EN 61000-3-2 Built in actif power corrector (PFC).
PRACTICAL : Output voltage adjustable from 10 to 15 V.
PROTECTED : Short circuit protection.
EASY : Direct DIN rail mounting.
– Plug-in terminal blocks.

Download documentationDownload the quick user manual

144,00  HT

DIN RAIL regulated switching power supply : 12V (Adj.10 to15V) ; 120W

EAN: 3760244880260 Ref. : ALE1210 Categories , Tag

PRECISE : Output ripple < 3 mV rms.
COMPLIE : EN 61000-3-2 Built in actif power corrector (PFC).
PRACTICAL : Output voltage adjustable from 10 to 15 V.
PROTECTED : Short circuit protection.
EASY : Direct DIN rail mounting.
– Plug-in terminal blocks.

Download documentationDownload the quick user manual

144,00  HT

Description

Voltage
• Floating outputs on dual spring terminal block for 2.5mm² (AWG 12) wire
• Output voltage : adjustable from 10 to 15 V.
• Regulation : < 25 mV for a load variation from 0 to 100%.
< 1 mV for a line variation from -10 to +10%.
• Ripple : < 3 mV rms including:
< 5 mV peak to peak of the signal at 100 kHz
< 5 mV peak to peak of the signal at 100 Hz
< 35 mV peak to peak of switching spikes
• Hold-up time : 25 ms at half load and 12 ms at full load (190 V line input).
• Indicator : green power-on LED indicator.
“status, output fault” red LED.

Current
• Max I : 10,5 A in short circuit condition.
10 A from 10 to 15 V

Power
• Max output power : 150 W.

Protection
• Short circuit protection, by current limit.
• Against overcurrent on main input, by fuse.
• Output overload protection by voltage limiting to 17 V.

Other specifications
• Safety : Complies with EN 61010-1, EN61010-2-201 and EN 62368-1.
• EMC : Complies with EN 61000-6-2 and EN 61000-6-4.
• Insulation Class : I
• Overvoltage Category : II
• Pollution Degree : 2
• Installation altitude : < 2000 m
• Protection level : IP 30
• Operating temperature: from -10 to +60 °C ; derating : 2.5 %/K from +45 °C
• Input voltage : 190 to 264 Volts, 50-60 Hz.
• Mains input : Dual spring terminal block for 2.5 mm² (AWG 12) wire.
• Power consumption: 175 W max.
• Power factor : 0,99 (built with PFC).
• Dielectric strength : 3000 VAC.
1800 VAC from input to chassis.
• Presentation :galvanized steel case and front panel with epoxy finish.
• Mounting :Integral symmetrical DIN rail clips

Additional information

Nombre de voie

1 channel

Puissance

120 WATTS

Volts

12 V, 12 V (Aj 10 à 15 V), 13,6 V, PRIM. 230 V

Ampères

10 A

Regulations

• Safety : Complies with EN 61010-1, EN61010-2-201 and EN 62368-1.
• EMC : Complies with EN 61000-6-2 and EN 61000-6-4.
• Insulation Class : I
• Overvoltage Category : II
• Pollution Degree : 2
• Installation altitude : < 2000 m
• Protection level : IP 30